The paper discusses causally-defined effects for mediation analysis in an SEM context for continuous, binary, ordinal, nominal, and count variables. With non-continuous variables, causally-defined effects have not been available in SEM software until now. The paper discusses maximum-likelihood and Bayesian analysis for non-normal effects, latent response variable mediators, Monte Carlo simulations for planning new studies, sensitivity analysis when violating sequential ignorability, and generalizations to continuous and categorical latent variables. Furthermore, the paper is the first to present a method for mediation with a nominal mediator. One of the illustrations is an analysis of Judea Pearl's hypothetical example with binary mediator and binary outcome that was debated on SEMNET in September.
Mplus users who do mediation analysis are urged to study the paper in the previous posting. The research in this paper elaborates and extends our previous recommendations of how to report indirect and direct effects.
Some of the analyses performed in the new paper require Mplus Version 6.12 which is scheduled to be released next week.
I have just read the new paper on Mediation and had a couple of basic questions.
1) How are the DE, TIE, PIE parameters interpreted for a count or negative binomial outcome? It looks as though parameters are exponentiated before being entered into these formulas from the example code in the table 51-2.
2) I am also new to the Causal Effect modeling approach, so I will go back and read some more of the introductory papers, but I wondered what the basic change to the formulas would be with say 3 or 4 treatments as opposed to two conditions.
When examining mediation using parallel process growth models, several studies have looked at the relationship between X (e.g.-tx condition) and subsequent M & Y parallel process models. However, I have not been able to locate any examples for which X & M are parallel process models and Y is a future outcome.
Do you see any inherent methodological problems for a model in which the relationship between both initial status and growth of X and its relationship with the future outcome Y is thought to be mediated by the slope of M?
If such a model is plausible, does the model presented below appear to represent an adequate means for examining such a relationship?
I'm brand new to MPlus so I apologize if this is extremely basic.I am attempting to decompose several significant interactions. I have one categorical predictor (sexual victimization history) and have found that my continuous moderators (life stress and social support) significantly moderate the relationship between my predictor and outcome variables (of which I have three--all are categorical). Can I do this in Mplus?
Yes, you can do this. See Example 3.18. It is more complicated than your model but you should be able to use that as a starting point.
Boliang Guo posted on Wednesday, March 19, 2014 - 2:43 am
2011 paper is really great!! especially for model with nominal mediator, thank. Here is also two more points in my mind for your kind attention, based on equation (16), could I say the PIE is mathematically equivalent to the traditional mediation estimate, e.g a*b? could the definition be generalized to case when x is continuous variable? i.e. X is not the treatment status but the dose of drug, so the effect of X is change in y due to unit change in x?thanks.
If I wanted to use the model constraint command to estimate create a sensitivity plot of a treatment outcome error correlation rather than a treatment mediator correlation is it correctly understood that I can use the estimate of beta1 in "run 23" in your 2011 paper on causal mediation analysis?
I.e. an example with a treatment an outcome and two independent variables:
MODEL: outcome with treatment (cov) ; outcome (sig) ; treatment (sig2) ; outcome on x1 x2; treatment on x1 x2 ; MODEL CONSTRAINT: plot(beta1) ; loop(mod, -1,1,0.1) ; NEW(rhocurl rho) ; rhocurl=cov/(sqrt(sig)*sqrt(sig2)) ; rho=mod ; beta1=(sqrt(sig)/sqrt(sig2))*(rhocurl-rho*sqrt((1-rhocurl*rhocurl)/(1-rho*rho))) ; plot: type=plot2 ;
Hi Bengt thank you for your response. I have essentially just reproduced the script from "run24" where I use "beta1" which is the effect of the mediator on the outcome variable but do not multiply it with the effect of the treatment on the mediator to obtain the indirect effect but simply keep the "direct" effect. Would this not simply correspond to the "total" effect if it is not theorized to be a mediator but simply the total effect of an independent variable after the other independent variables are held constant, and thus obtain the sensitivity of the treatment-outcome relationship of an error correlation between the two e.g. an unobserved confounder?
We originally fit an SEM model with one predictor, 2 mediators at time point 1, 2 mediators at time point 2 (that are the same, therefore there is a path from time 1 to time 2) and 3 outcome variables. Reviewers recommended that we explore causal mediation, and more specifically Imai et al.’s sensitivity analyses. I found the paper (Applications of causally defined direct and indirect effects in mediation analysis using SEM in Mplus) and code for these analyses but I am unsure how to extend them to a model with multiple mediators and outcomes.
I am able to include the other pathways when I code a single pathway for the sensitivity analyses, but it won’t let me specify the indirect effects. Is there a way to code this, and particularly for calculating indirect effects through two mediators (predictor – mediator1 – mediator 2- outcome) similar to using the VIA command? Can these analyses be done with multiple mediators?
I have also noticed that when I specify a single pathway (predictor- mediator-outcome) the “INDIRECT” coefficient under New/Additional parameters is much larger than the coefficient using a simple mediation model when the rho is set to 0. Is there a reason for this?
Finally, is there code for the graphs which show how the effect is altered over a range of rho values? I saw that the LOOP command could be used, but I did not have any success in coding this.
There is an interesting paper in a 2015 issue of Amer J of Epi:
Mediation Analysis With Intermediate Confounding: Structural Equation Modeling Viewed Through the Causal Inference Lens Bianca L. De Stavola et al
Bianca's L and M can be seen as sequential mediators and she presents Mplus scripts.
I am not aware of sensitivity analyses with multiple mediators. I would think Imai's approach can be generalized bu I haven't tried that yet.
You can do VIA when you have multiple mediators.
For a zero rho value I would expect the same indirect effect as obtained using Model Indirect.
Mplus 7.4 automatically does a sensitivity plot when there is one mediator. In the PLOT command just say
shaun goh posted on Friday, July 29, 2016 - 2:48 am
Dear Dr Muthens,
I have questions about the treatment-mediator as moderator model, specifically Figure 1 of 'Causal effects in Mediation modelling : An introduction with applications to latent variables' (2015) as follows
-To model Figure 1, I would need to do declare X, M(mediator), and XM as predictors, and also use 'MODEL INDIRECT : y MOD M XM X'
-I'm struggling to understand the nuances of the model. Are there texts/papers you would recommend that have used this model or give insight into the interpretation of the treatment-mediator as moderation effect?
-I believe my mediator interacts with my treatment, and am afraid it will violate the assumptions of a simple mediation model. Is this a good motivation to use this model?