Message/Author 


Hello, At this moment I am running a multilevel model with a crosslevel interaction using the MLR estimator. Above my model results I find the following warning: MAXIMUM LOGLIKELIHOOD VALUE FOR THE UNRESTRICTED (H1) MODEL IS 1011.058 WARNING: THE MODEL ESTIMATION HAS REACHED A SADDLE POINT OR A POINT WHERE THE OBSERVED AND THE EXPECTED INFORMATION MATRICES DO NOT MATCH.AN ADJUSTMENT TO THE ESTIMATION OF THE INFORMATION MATRIX HAS BEEN MADE. THE CONDITION NUMBER IS 0.672D03. THE PROBLEM MAY ALSO BE RESOLVED BY DECREASING THE VALUE OF THE MCONVERGENCE OR LOGCRITERION OPTIONS OR BY CHANGING THE STARTING VALUES OR BY USING THE MLF ESTIMATOR. THE MODEL ESTIMATION TERMINATED NORMALLY For me, this warning sounds like Mplus made an adjustment and that I can interpret my crosslevel interaction. Is this correct? Or do I need to make an additional adjustment myself? The strange thing is that the crosslevel interaction disappears when I change the estimator from MLR to MLF... Does this mean that the identified crosslevel interaction is a statistical artefact? I hope that someone can help me with this. Thanks in advance for your reaction. Best, Martine 


This warning can be ignored and the results interpreted. The MLF standard errors are often unnecessarily large  I would stay with your MLR output. 


I have also estimated a multilevel model to estimate a crosslevel interaction and obtain a similar error message. I have two questions: (1) When is it safe to "ignore" the warning ? When it says that the model estimation terminated normally? And (2) how would you report this in an article? That an adjustment to the information matrix has been made and then make a reference to the article by Tihomir and Bengt on the issue http://www.statmodel.com/download/SaddlePoints2.pdf ? Or not mention it at all since the model estimated normally? My warning message is this: WARNING: THE MODEL ESTIMATION HAS REACHED A SADDLE POINT OR A POINT WHERE THE OBSERVED AND THE EXPECTED INFORMATION MATRICES DO NOT MATCH. AN ADJUSTMENT TO THE ESTIMATION OF THE INFORMATION MATRIX HAS BEEN MADE. THE CONDITION NUMBER IS 0.998D03. THE PROBLEM MAY ALSO BE RESOLVED BY DECREASING THE VALUE OF THE MCONVERGENCE OR LOGCRITERION OPTIONS OR BY CHANGING THE STARTING VALUES OR BY USING THE MLF ESTIMATOR. THE MODEL ESTIMATION TERMINATED NORMALLY 


(1) I think it is typically safe to ignore the warning; it is mainly given as information about which SE estimator is used. If you can eliminate reasons 1. and 2. mentioned in the tech note that you refer to, then you should be fine. (2) I would report that the SEs are computed with this method, giving a reference to the tech note. 


I estimated a multilevel model with crosslevel interactions. I used integration = montecarlo and mconvergence = .01, MLR, and ADAPTIVE = off; I obtained the WARNING: THE MODEL ESTIMATION HAS REACHED A SADDLE POINT message. Based on recommendations in the tech report about saddle points, I reran the model with 500 integration points (I read this is normally the standard; the original model where I made no specifications on number of integration points had 326) and mconvergence = .001. I also included STARTS 150 15; the message did not go away. At that point, I upped to 5000 integration points given the manual states this is a good idea if you have more than 3 dimensions (I have 4). Still get the message. Dr. Bengt Muthen notes above that the Saddle point warning can be ignored as it generally only affects SE estimation but I noticed that in the models with more integration points and the smaller convergence value, the effects of the cross level interactions were no longer significant (one was in the original model) and the level 2 parameter estimates all diminished slightly (including my level 2 main effect, which is .083 and significant(p=.046) in the original model, .079 (p=.056) in the 500 integration model, and .077 (p= .142) in 5000 integration point model. I am worried does this suggest the results I found with fewer integration points and larger mconvergence are not trustworthy? 


The more integration points and the sharper convergence criterion, the more precise the logL, estimates, and SEs. You have do do trial and error. You can even use the default integ=15, which with 4 dimensions gives 50625 integration points, that is, many more than the 5000 of Monte Carlo integration. It will be slower, however. Generally speaking, I don't think you want to have as lax of a convergence criterion as mconv =0.01. 

S REN posted on Wednesday, February 14, 2018  7:07 pm



I have a similar question. With this warning, I don't seem to have the results of CFI, TLI etc. In this case, how can I get the model fit? Thanks. 


Numerical integration is typically done with categorical or other noncontinuous outcomes where the usual mean and covariance structure testing isn't relevant but models are instead compared via BIC. 

S REN posted on Thursday, February 15, 2018  8:22 pm



Thanks. The model I am trying to assess is a 111 model with a Level 2 moderator and the Level 2 moderator is (0,1) treating as continuous. However, I still got this warning and do not have CFI, TLI..Could you advise how I can get the model fit please? 


Please send your output to Support along with your license number. 

S REN posted on Saturday, February 17, 2018  7:46 pm



Thank you for your response. I'll send it shortly. Before I do so, I just want to quickly ask about one final question to make sure that the syntax I wrote is correct. I want to test a model with level 1 variables as below XMediator1Mediator2DV and a Level 1 moderator moderates the relationship between Mediator1 and Mediator 2. so should I write DV ON Mediator2 Mediator1; Mediator2 ON Mediator1 Moderator InteractionTerm; Or should I write DV ON Mediator2 Mediator1 Moderator InteractionTerm; Mediator2 ON Mediator1 Moderator InteractionTerm; Thank you! 


See our book Regression and Mediation Analysis using Mplus. 


The second alternative is more rigorous. 

Back to top 